Publikationer från Malmö universitet
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Residual stresses in TiN, DLC and MoS2 coated surfaces with regard to their tribological fracture behaviour
Visa övriga samt affilieringar
2009 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 267, nr 12, s. 2142-2156Artikel i tidskrift (Refereegranskat)
Abstract [en]

Thin hard coatings on components and tools are used increasingly due to the rapid development in deposition techniques, tribological performance and application skills. The residual stresses in a coated surface are crucial for its tribological performance. Compressive residual stresses in PVD deposited TiN and DLC coatings were measured to be in the range of 0.03–4 GPa on steel substrate and 0.1–1.3 GPa on silicon. MoS2 coatings had tensional stresses in the range of 0.8–1.3 on steel and 0.16 GPa compressive stresses on silicon. The fracture pattern of coatings deposited on steel substrate were analysed both in bend testing and scratch testing. A micro-scale finite element method (FEM) modelling and stress simulation of a 2 μm TiN-coated steel surface was carried out and showed a reduction of the generated tensile buckling stresses in front of the sliding tip when compressive residual stresses of 1 GPa were included in the model. However, this reduction is not similarly observed in the scratch groove behind the tip, possibly due to sliding contact-induced stress relaxation. Scratch and bending tests allowed calculation of the fracture toughness of the three coated surfaces, based on both empirical crack pattern observations and FEM stress calculation, which resulted in highest values for TiN coating followed by MoS2 and DLC coatings, being KC = 4–11, about 2, and 1–2 MPa m1/2, respectively. Higher compressive residual stresses in the coating and higher elastic modulus of the coating correlated to increased fracture toughness of the coated surface.

Ort, förlag, år, upplaga, sidor
2009. Vol. 267, nr 12, s. 2142-2156
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:mau:diva-2513DOI: 10.1016/j.wear.2009.01.004ISI: 000272810200002Scopus ID: 2-s2.0-71849114739Lokalt ID: 9479OAI: oai:DiVA.org:mau-2513DiVA, id: diva2:1399276
Tillgänglig från: 2020-02-27 Skapad: 2020-02-27 Senast uppdaterad: 2024-02-06Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Person

Ståhle, Per

Sök vidare i DiVA

Av författaren/redaktören
Ståhle, Per
Av organisationen
Teknik och samhälle (TS)
I samma tidskrift
Wear
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 30 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf